Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of RADILON DT 40E50USR 333C BK - PA612 - RadiciGroup High Performance Polymers

Material Data Center offers the following functions for RADILON DT 40E50USR 333C BK:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Radilon DT datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Propriétés mécaniques - Propriétés thermiques - Propriétés électriques - Propriétés diverses
Any use of this information falls under the rules of our disclaimer.
Informations produit
PA612 semi-rigid, high viscosity extrusion grade. Toughened. Improved resistance to uric acid solutions. Black colour.

Suitable for extrusion of profiles, tubes and pipes. Material especially developed for automotive under the hood applications, employed in selective catalytic reductions (SCR) systems.
Propriétés mécaniquessec / condUnitéNorme du test
ISO Data
Module en traction 920 / - MPa ISO 527
Contrainte d'écoulement 30 / - MPa ISO 527
Déformation au seuil d'écoulement 25 / - % ISO 527
Résistance au choc Charpy (entaillé), +23°C 85 / - kJ/m² ISO 179/1eA
Résistance au choc Charpy (entaillé), -30°C 68 / - kJ/m² ISO 179/1eA
Propriétés thermiquessec / condUnitéNorme du test
ISO Data
Température de fusion, 10°C/min 212 / * °C ISO 11357-1/-3
Propriétés électriquessec / condUnitéNorme du test
ISO Data
Résistivité transversale 1E13 / 1E11 Ohm*m IEC 62631-3-1
Résistivité superficielle * / 1E10 Ohm IEC 62631-3-2
Propriétés diversessec / condUnitéNorme du test
Absorption d'eau 2 / * % Sim. to ISO 62
Absorption d'humidité 0.8 / * % Sim. to ISO 62
Masse volumique 1010 / - kg/m³ ISO 1183
Caractéristiques
Transformation
Moulage par injection, Extrusion de tubes, Extrusion de profilés
Conditionnement
Grains, Noir
Propriétés spéciales
Stabilisé à la chaleur
Résistance Chimique
Résistance aux acides
Applications
Automobile
Disponibilité régionale
Amérique du nord, Europe, Asia Pacific, South and Central America, Proche-Orient/Afrique
Autres informations
Moulages par injection
The material is delivered in moisture-proof packaging ready for processing. Maximum recommended water content for best processing is 0.10%. Typical conditions with a desiccant drier: temperature 80 ° C, dew point -20 ° C or below, time 2-4 h or more. Avoid excessive shear rates and high thermal stresses for better processing. Special care must be taken to avoid moisture absorption and contamination with other polymers when adding regrind material. Colour variation and mechanical properties reduction may occur and should always be carefully monitored.

Injection Molding Processing Parameters:
Melt Temperature Mold Temperature Injection Speed
230 - 260°C 70 - 80°C medium

Extrusion Processing Parameters:
Rear Center Rear   Center Front   Front Head and Die   Melt Temp
220°C 250°C 260°C 270°C 275 - 280°C 275°C
428°F 482°F 500°F 518°F 527 - 536°F 527°F
Conditions générales
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.